Top 18 Cobalt Steel Square Nose End Mills

 

Niagara Cutter N88401 Cobalt Steel Square Nose End Mill Weldon Shank TiCN Finish Roughing Cutting Non-Center Cutting 30-Degree 4-Flute 3875 OAL 0750 Cut Diameter 0750 Shank Diameter

Niagara Cutter N88401 Cobalt Steel Square Nose End Mill, Weldon Shank, TiCN Finish, Roughing Cutting, Non-Center Cutting, 30-Degree, 4-Flute, 3.875″ OAL, 0.750″ Cut Diameter, 0.750″ Shank Diameter

Niagara Cutter N88401 Cobalt Steel Square Nose End Mill, Weldon Shank, TiCN Finish, Roughing Cutting, Non-Center Cutting, 30-Degree, 4-Flute, 3.875″ OAL, 0.750″ Cut Diameter, 0.750″ Shank Diameter - Number of flutes varies by diameter for optimum feed and cut rate. Titanium carbon nitride (ticn) coating lubricates the end mill for high-temperature stability and offers better abrasion resistance than tin coating. Fine-pitch tooth design is suitable for machining high-temperature alloys. Roughing end mills have chip-breaking cutting edges that remove material in less time than conventional end mills. Square end creates sharp, unrounded cuts and has a corner chamfer to strengthen the cutting edges.

 

Melin Tool E Cobalt Steel Square Nose End Mill Weldon Shank Uncoated Bright Finish 30 Deg Helix 3 Flutes 23125 Overall Length 01250 Cutting Diameter 03750 Shank Diameter

Melin Tool E Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, 30 Deg Helix, 3 Flutes, 2.3125″ Overall Length, 0.1250″ Cutting Diameter, 0.3750″ Shank Diameter

Melin Tool E Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, 30 Deg Helix, 3 Flutes, 2.3125″ Overall Length, 0.1250″ Cutting Diameter, 0.3750″ Shank Diameter - Used for general purpose milling in most materials of medium and tough alloy materials such as stainless steel, nickel base alloy, brass, iron etc. 3 flutes usually allow feed rates 50 percent faster than 2 flute tools. Weldon shanks feature a round shank with one of more flats machined into the side for easy indexing and alignment. Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. Cobalt steel tools are similar to high-speed steel, but with more cobalt for improved performance when cutting harder metals such as stainless steel or nickel alloys.

 

Melin Tool CS-A Cobalt Steel Square Nose End Mill Weldon Shank Uncoated Bright Finish Non-Center Cutting 30 Deg Helix 6 Flutes 3 Overall Length 12500 Cutting Diameter 075 Shank Diameter

Melin Tool CS-A Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, Non-Center Cutting, 30 Deg Helix, 6 Flutes, 3″ Overall Length, 1.2500″ Cutting Diameter, 0.75″ Shank Diameter

Melin Tool CS-A Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, Non-Center Cutting, 30 Deg Helix, 6 Flutes, 3″ Overall Length, 1.2500″ Cutting Diameter, 0.75″ Shank Diameter - Not to be used for plunge cutting. Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. Can be used in profiling, keyways, and pockets. Weldon shanks feature a round shank with one of more flats machined into the side for easy indexing and alignment. Cobalt steel tools are similar to high-speed steel, but with more cobalt for improved performance when cutting harder metals such as stainless steel or nickel alloys.

 

Niagara Cutter N43773 Cobalt Steel Square Nose End Mill Weldon Shank TiCN Finish RoughingFinishing Cut Non-Center 30-Degree 6-Flute 75 OAL 1500 Cut Diameter 1250 Shank Diameter

Niagara Cutter N43773 Cobalt Steel Square Nose End Mill, Weldon Shank, TiCN Finish, Roughing/Finishing Cut, Non-Center, 30-Degree, 6-Flute, 7.5″ OAL, 1.500″ Cut Diameter, 1.250″ Shank Diameter

Niagara Cutter N43773 Cobalt Steel Square Nose End Mill, Weldon Shank, TiCN Finish, Roughing/Finishing Cut, Non-Center, 30-Degree, 6-Flute, 7.5″ OAL, 1.500″ Cut Diameter, 1.250″ Shank Diameter - Square nose end mills (also called square end) create sharp, unrounded cuts. Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel. Titanium carbon nitride (ticn) coating lubricates the end mill for high-temperature stability and offers better abrasion resistance than tin coating. Truncated rougher-finisher removes material in less time than conventional end mills while producing a finer finish than fine- or coarse-pitch roughers. Number of flutes varies by diameter for optimum feed and cut rate.

 

Melin Tool CC-L Cobalt Steel Square Nose End Mill Weldon Shank Uncoated Bright Finish 30 Deg Helix 4 Flutes 26250 Overall Length 01563 Cutting Diameter 03750 Shank Diameter

Melin Tool CC-L Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, 30 Deg Helix, 4 Flutes, 2.6250″ Overall Length, 0.1563″ Cutting Diameter, 0.3750″ Shank Diameter

Melin Tool CC-L Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, 30 Deg Helix, 4 Flutes, 2.6250″ Overall Length, 0.1563″ Cutting Diameter, 0.3750″ Shank Diameter - Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. 30 degree helix angle. Used for general purpose milling in most materials of medium and tough alloy materials such as stainless steel, nickel base alloy, brass, iron, etc. Cobalt steel tools are similar to high-speed steel, but with more cobalt for improved performance when cutting harder metals such as stainless steel or nickel alloys. Weldon shanks feature a round shank with one of more flats machined into the side for easy indexing and alignment.

 

Niagara Cutter N72869 Cobalt Steel Square Nose End Mill Metric Weldon Shank Uncoated Bright Finish Finishing Cut 30 Degree Helix 4 Flutes 3375 Overall Length 14mm Cutting Diameter 0500 Shank Diameter

Niagara Cutter N72869 Cobalt Steel Square Nose End Mill, Metric, Weldon Shank, Uncoated (Bright) Finish, Finishing Cut, 30 Degree Helix, 4 Flutes, 3.375″ Overall Length, 14mm Cutting Diameter, 0.500″ Shank Diameter

Niagara Cutter N72869 Cobalt Steel Square Nose End Mill, Metric, Weldon Shank, Uncoated (Bright) Finish, Finishing Cut, 30 Degree Helix, 4 Flutes, 3.375″ Overall Length, 14mm Cutting Diameter, 0.500″ Shank Diameter - Square nose end mills (also called square end) create sharp, unrounded cuts. Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel. Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials. Four flutes produce a better finish than fewer flutes. Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling.

 

YG-1 E2172 Cobalt Steel Square Nose End Mill Long Reach Weldon Shank Uncoated Bright Finish Roughing Cut Non-Center Cutting 30 Deg Helix 5 Flutes 625 Overall Length 1 Cutting Diameter 075 Shank Diameter

YG-1 E2172 Cobalt Steel Square Nose End Mill, Long Reach, Weldon Shank, Uncoated (Bright) Finish, Roughing Cut, Non-Center Cutting, 30 Deg Helix, 5 Flutes, 6.25″ Overall Length, 1″ Cutting Diameter, 0.75″ Shank Diameter

YG-1 E2172 Cobalt Steel Square Nose End Mill, Long Reach, Weldon Shank, Uncoated (Bright) Finish, Roughing Cut, Non-Center Cutting, 30 Deg Helix, 5 Flutes, 6.25″ Overall Length, 1″ Cutting Diameter, 0.75″ Shank Diameter - Number of flutes varies by diameter for optimum feed and cut rate. Roughing end mills have chip-breaking cutting edges that remove material in less time than conventional end mills. Long-length end mills have longer cutting edges than standard- and medium-length end mills for increased cutting length. Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel. Coarse-pitch tooth design and tool geometry are suitable for high-production metal removal on cutting- steel grades and many nonferrous materials.

 

Niagara Cutter N14560 Cobalt Steel Square Nose End Mill Inch Weldon Shank TiAlN Finish Roughing Cut 30 Degree Helix 4 Flutes 225 Overall Length 0375 Cutting Diameter 0375 Shank Diameter

Niagara Cutter N14560 Cobalt Steel Square Nose End Mill, Inch, Weldon Shank, TiAlN Finish, Roughing Cut, 30 Degree Helix, 4 Flutes, 2.25″ Overall Length, 0.375″ Cutting Diameter, 0.375″ Shank Diameter

Niagara Cutter N14560 Cobalt Steel Square Nose End Mill, Inch, Weldon Shank, TiAlN Finish, Roughing Cut, 30 Degree Helix, 4 Flutes, 2.25″ Overall Length, 0.375″ Cutting Diameter, 0.375″ Shank Diameter - Number of flutes varies by diameter for optimum feed and cut rate. Roughing end mills have chip-breaking cutting edges that remove material in less time than conventional end mills. Square end creates sharp, unrounded cuts and has a corner chamfer to strengthen the cutting edges. Titanium aluminum nitride (tialn) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than tin and ticn coatings. Fine-pitch tooth design is suitable for machining high-temperature alloys.

 

YG-1 E2172 Cobalt Steel Square Nose End Mill Long Reach Weldon Shank Uncoated Bright Finish Roughing Cut Non-Center Cutting 30 Deg Helix 4 Flutes 4 Overall Length 05 Cutting Diameter 05 Shank Diameter

YG-1 E2172 Cobalt Steel Square Nose End Mill, Long Reach, Weldon Shank, Uncoated (Bright) Finish, Roughing Cut, Non-Center Cutting, 30 Deg Helix, 4 Flutes, 4″ Overall Length, 0.5″ Cutting Diameter, 0.5″ Shank Diameter

YG-1 E2172 Cobalt Steel Square Nose End Mill, Long Reach, Weldon Shank, Uncoated (Bright) Finish, Roughing Cut, Non-Center Cutting, 30 Deg Helix, 4 Flutes, 4″ Overall Length, 0.5″ Cutting Diameter, 0.5″ Shank Diameter - Roughing end mills have chip-breaking cutting edges that remove material in less time than conventional end mills. Long-length end mills have longer cutting edges than standard- and medium-length end mills for increased cutting length. Number of flutes varies by diameter for optimum feed and cut rate. Coarse-pitch tooth design and tool geometry are suitable for high-production metal removal on cutting- steel grades and many nonferrous materials. Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel.

 

YG-1 E2160 Cobalt Steel Square Nose End Mill Weldon Shank Uncoated Bright Finish 30 Deg Helix 3 Flutes 134375 Overall Length 01875 Cutting Diameter 025 Shank Diameter

YG-1 E2160 Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, 30 Deg Helix, 3 Flutes, 1.34375″ Overall Length, 0.1875″ Cutting Diameter, 0.25″ Shank Diameter

YG-1 E2160 Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, 30 Deg Helix, 3 Flutes, 1.34375″ Overall Length, 0.1875″ Cutting Diameter, 0.25″ Shank Diameter - Stub length increases the strength of the tool, making it less likely to break in the workpiece. Uncoated (bright) tools have no additional surface treatment or coating for a range of materials. Three flutes provide better chip-carrying capacity than four flutes and a finer finish than two, reducing the need for a second finishing cut in some applications. Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel. Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling.

 

Niagara Cutter N69332 Cobalt Steel Square Nose End Mill Weldon Shank TiCN Finish Roughing Cutting Non-Center Cutting 30-Degree 8-Flute 65 OAL 2000 Cut Diameter 1250 Shank Diameter

Niagara Cutter N69332 Cobalt Steel Square Nose End Mill, Weldon Shank, TiCN Finish, Roughing Cutting, Non-Center Cutting, 30-Degree, 8-Flute, 6.5″ OAL, 2.000″ Cut Diameter, 1.250″ Shank Diameter

Niagara Cutter N69332 Cobalt Steel Square Nose End Mill, Weldon Shank, TiCN Finish, Roughing Cutting, Non-Center Cutting, 30-Degree, 8-Flute, 6.5″ OAL, 2.000″ Cut Diameter, 1.250″ Shank Diameter - Roughing end mills have chip-breaking cutting edges that remove material in less time than conventional end mills. Coarse-pitch tooth design is suitable for machining soft, gummy materials. Titanium carbon nitride (ticn) coating lubricates the end mill for high-temperature stability and offers better abrasion resistance than tin coating. Square end creates sharp, unrounded cuts and has a corner chamfer to strengthen the cutting edges. Number of flutes varies by diameter for optimum feed and cut rate.

 

Melin Tool CFP Cobalt Steel Square Nose End Mill Weldon Shank Uncoated Bright Finish Roughing Cut Non-Center Cutting 30 Deg Helix 6 Flutes 42500 Overall Length 13750 Cutting Diameter 075 Shank Diameter

Melin Tool CFP Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, Roughing Cut, Non-Center Cutting, 30 Deg Helix, 6 Flutes, 4.2500″ Overall Length, 1.3750″ Cutting Diameter, 0.75″ Shank Diameter

Melin Tool CFP Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, Roughing Cut, Non-Center Cutting, 30 Deg Helix, 6 Flutes, 4.2500″ Overall Length, 1.3750″ Cutting Diameter, 0.75″ Shank Diameter - Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. A rough finish is produced which may require a finishing pass. These tools will not plunge cut. Round shanks allow use with a wide variety of toolholding systems. Cobalt steel tools are similar to high-speed steel, but with more cobalt for improved performance when cutting harder metals such as stainless steel or nickel alloys.

 

Melin Tool A Cobalt Steel Square Nose End Mill Weldon Shank Uncoated Bright Finish 30 Deg Helix 2 Flutes 31250 Overall Length 05938 Cutting Diameter 05 Shank Diameter

Melin Tool A Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, 30 Deg Helix, 2 Flutes, 3.1250″ Overall Length, 0.5938″ Cutting Diameter, 0.5″ Shank Diameter

Melin Tool A Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, 30 Deg Helix, 2 Flutes, 3.1250″ Overall Length, 0.5938″ Cutting Diameter, 0.5″ Shank Diameter - Suitable for general-purpose machining on most medium-hardness and tough materials, including stainless steel, nickel-based alloys, brass, and iron. Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel. Two flutes offer better chip-carrying capacity than end mills with more flutes, enhancing the tool’s ability to remove material. Uncoated (bright) tools have no additional surface treatment or coating for use on a range of materials. Square nose end mills (also called square end) create sharp, unrounded cuts.

 

YG-1 E2036 Cobalt Steel Square Nose End Mill Extra Long Reach Weldon Shank Uncoated Bright Finish Non-Center Cutting 30 Deg Helix 4 Flutes 625 Overall Length 075 Cutting Diameter 075 Shank Diameter

YG-1 E2036 Cobalt Steel Square Nose End Mill, Extra Long Reach, Weldon Shank, Uncoated (Bright) Finish, Non-Center Cutting, 30 Deg Helix, 4 Flutes, 6.25″ Overall Length, 0.75″ Cutting Diameter, 0.75″ Shank Diameter

YG-1 E2036 Cobalt Steel Square Nose End Mill, Extra Long Reach, Weldon Shank, Uncoated (Bright) Finish, Non-Center Cutting, 30 Deg Helix, 4 Flutes, 6.25″ Overall Length, 0.75″ Cutting Diameter, 0.75″ Shank Diameter - Four flutes produce a better finish than fewer flutes. Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel. Extra-long-length end mills have longer cutting edges than long-length end mills for increased cutting length. Uncoated (bright) tools have no additional surface treatment or coating for use on a range of materials. Square nose end mills (also called square end) create sharp, unrounded cuts.

 

Niagara Cutter N71329 Cobalt Steel Square Nose End Mill Weldon Shank TiCN Finish Roughing Cutting Non-Center Cutting 30-Degree 5-Flute 45 OAL 1000 Cut Diameter 1000 Shank Diameter

Niagara Cutter N71329 Cobalt Steel Square Nose End Mill, Weldon Shank, TiCN Finish, Roughing Cutting, Non-Center Cutting, 30-Degree, 5-Flute, 4.5″ OAL, 1.000″ Cut Diameter, 1.000″ Shank Diameter

Niagara Cutter N71329 Cobalt Steel Square Nose End Mill, Weldon Shank, TiCN Finish, Roughing Cutting, Non-Center Cutting, 30-Degree, 5-Flute, 4.5″ OAL, 1.000″ Cut Diameter, 1.000″ Shank Diameter - Titanium carbon nitride (ticn) coating lubricates the end mill for high-temperature stability and offers better abrasion resistance than tin coating. Number of flutes varies by diameter for optimum feed and cut rate. Square end creates sharp, unrounded cuts and has a corner chamfer to strengthen the cutting edges. Roughing end mills have chip-breaking cutting edges that remove material in less time than conventional end mills. Coarse-pitch tooth design is suitable for machining soft, gummy materials.

 

Niagara Cutter N88621 Cobalt Steel Square Nose End Mill Inch Weldon Shank TiCN Finish Finishing Cut 30 Degree Helix 4 Flutes 325 Overall Length 0500 Cutting Diameter 0500 Shank Diameter

Niagara Cutter N88621 Cobalt Steel Square Nose End Mill, Inch, Weldon Shank, TiCN Finish, Finishing Cut, 30 Degree Helix, 4 Flutes, 3.25″ Overall Length, 0.500″ Cutting Diameter, 0.500″ Shank Diameter

Niagara Cutter N88621 Cobalt Steel Square Nose End Mill, Inch, Weldon Shank, TiCN Finish, Finishing Cut, 30 Degree Helix, 4 Flutes, 3.25″ Overall Length, 0.500″ Cutting Diameter, 0.500″ Shank Diameter - Square nose end mills (also called square end) create sharp, unrounded cuts. Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel. Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling. Titanium carbon nitride (ticn) coating lubricates the end mill for high-temperature stability and offers better abrasion resistance than tin coating. Number of flutes varies fewer flutes have more chip-carrying capacity and more flutes produce a finer finish.

 

Niagara Cutter N69291 Cobalt Steel Square Nose End Mill Weldon Shank TiCN Finish Roughing Cutting Non-Center Cutting 30-Degree 4-Flute 3063 OAL 0250 Cut Diameter 0375 Shank Diameter

Niagara Cutter N69291 Cobalt Steel Square Nose End Mill, Weldon Shank, TiCN Finish, Roughing Cutting, Non-Center Cutting, 30-Degree, 4-Flute, 3.063″ OAL, 0.250″ Cut Diameter, 0.375″ Shank Diameter

Niagara Cutter N69291 Cobalt Steel Square Nose End Mill, Weldon Shank, TiCN Finish, Roughing Cutting, Non-Center Cutting, 30-Degree, 4-Flute, 3.063″ OAL, 0.250″ Cut Diameter, 0.375″ Shank Diameter - Square end creates sharp, unrounded cuts and has a corner chamfer to strengthen the cutting edges. Coarse-pitch tooth design is suitable for machining soft, gummy materials. Titanium carbon nitride (ticn) coating lubricates the end mill for high-temperature stability and offers better abrasion resistance than tin coating. Roughing end mills have chip-breaking cutting edges that remove material in less time than conventional end mills. Number of flutes varies by diameter for optimum feed and cut rate.

 

YG-1 E2040 Cobalt Steel Square Nose End Mill Long Reach Weldon Shank Uncoated Bright Finish 30 Deg Helix 4 Flutes 325 Overall Length 0375 Cutting Diameter 0375 Shank Diameter

YG-1 E2040 Cobalt Steel Square Nose End Mill, Long Reach, Weldon Shank, Uncoated (Bright) Finish, 30 Deg Helix, 4 Flutes, 3.25″ Overall Length, 0.375″ Cutting Diameter, 0.375″ Shank Diameter

YG-1 E2040 Cobalt Steel Square Nose End Mill, Long Reach, Weldon Shank, Uncoated (Bright) Finish, 30 Deg Helix, 4 Flutes, 3.25″ Overall Length, 0.375″ Cutting Diameter, 0.375″ Shank Diameter - Four flutes produce a better finish than fewer flutes. Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel. Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling. Long-length end mills have longer cutting edges and can make deeper cuts than standard-length end mills. Uncoated (bright) tools have no additional surface treatment or coating for use on a range of materials.





We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.